Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Abilene Homeowners Choose Gelco Chimney Cleaning
We provide independent Gelco service in Abilene, from multi-flue and single-flue cap replacement to top-sealing damper repair, and we handle it as part of a full sweep, inspection, and repair visit. What makes our Gelco work different is fit: we match the cap to your actual flue dimensions and check the crown, mesh, and gasket in the same trip, so a small hardware failure doesn’t turn into water damage or a draft problem. Our technicians have up to experience with Gelco caps and dampers, and we’re an independent service provider – we’re not affiliated with or authorized by Gelco.
Abilene’s weather is hard on chimney hardware. The house is in West Texas, and the same dry wind that brings caliche dust and mesquite pollen in spring packs spark screens and cap mesh until draft drops and smoke rolls back into the room. That’s the number one reason Gelco owners in Abilene call us. Call (888) 359-2615 to book.
Why Trust Chimney Sweep Abilene for Your Gelco Chimney Cleaning?
Gelco caps and dampers are built to specific mounting patterns and clearances, and the difference between a five-year cap and a twenty-year one is usually whether the installer measured the flue properly and seated the legs on solid crown. Our technicians have serviced enough Gelco installations to know where those fail first: the bolt points on a multi-flue cap, the gasket edge on a top-sealing damper, the powder coat on a south-facing lid. That familiarity is what keeps your unit running the way it was designed.
We use quality parts that fit Gelco equipment. We don’t claim to stock OEM or genuine Gelco parts, and we’re not a Gelco dealer. When exact fit and warranty continuity matter, we specify parts to match the original spec; when a standard stainless equivalent will do the job on a single-flue application, we’ll say so.
Warranty-safe practice matters here too. We document what we find on camera, photograph the cap and damper before and after, and hand you the evidence so any future claim has a paper trail. If a manufacturer’s warranty question comes up, we can work through it with you. One company handles the sweep, the inspection, and the fix – no referrals, no gaps. Call (888) 359-2615 for a free estimate.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common Gelco Chimney Cleaning Problems We Fix in Abilene
Gelco hardware fails in predictable ways, and most of the calls we run in Abilene trace back to one of these five.
- Multi-flue cap legs loosening or corroding at the mounting bolts. The legs carry the whole weight of the cap, and when a bolt backs out or rusts through, the lid rattles in the wind and lets water run down around the crown. In Abilene’s gusty spring, a loose cap can lift and drop enough to widen the mounting holes, which is why we check torque and bolt condition on every visit.
- Top-sealing damper gaskets hardening or tearing. The gasket is the seal – a rubber or foam edge that has to compress flat when the damper closes. Long hot summers with the damper shut and the flue baking dry that gasket until it cracks. Once it goes, you get drafts down the flue, moisture entry when it rains, and heat escaping up the chimney in winter. It’s a cheap part and a common repair.
- Powder-coated finishes chalking and peeling in UV-heavy West Texas sun. A black powder-coated cap takes direct sun for years on end, and the finish eventually chalks and flakes. Once the bare steel underneath is exposed, rust sets in at the panel edges and along the seams. It’s not an emergency, but it’s not something to ignore either – a repaint or replacement before the rust pits saves the frame.
- Custom cap screens clogging with creosote and soot. Every custom Gelco cap has a spark screen sized to the flue, and that mesh collects creosote the way a filter collects dust. Clogged mesh chokes draft, and a choked flue sends smoke back into the firebox instead of up and out. It’s the most common cause of the “my fireplace suddenly smokes” call we get in Abilene.
- Water intrusion around the crown where the cap seats. A cap that’s out of square or sitting on a cracked crown lets water track down the flue liner. That shows up as staining on the firebox walls long before it shows up anywhere else. We check the crown seal as part of any cap service.
Gelco Parts & Our Repair-vs-Replace Approach
Most Gelco service calls come down to a repair, not a replacement. If the cap frame, damper housing, or mesh is structurally sound, we repair it – replace the gasket, re-seat the bolts, clear the screen, re-seal the crown. Replacement is reserved for the cases that make it the right call: failed welds, rust-through on the frame, or a cap whose dimensions no longer match the flue after a rebuild or a crown change.
On parts, we spec OEM-equivalent quality that fits Gelco hardware when exact fit and warranty continuity matter. For standard single-flue applications, a quality stainless aftermarket cap often does the same job for a meaningful savings, and we’ll tell you plainly when that’s the case. We don’t claim to stock genuine Gelco parts – what we can do is measure your flue, match the cap, and install it correctly. A sweep without an inspection is a guess. We do both. Call (888) 359-2615 for a free estimate.
Our Gelco Service Process – Step by Step
- 1
Diagnosis. We start with a camera inspection of the flue and a physical check of the cap or damper – mounting bolts, gasket condition, powder coat, mesh, and the crown seal around the base. You see the photos before we recommend anything.
- 2
Repair or install. Depending on what we find, we replace the gasket, re-seat the cap, replace the cap with a correctly sized unit, or fabricate a custom cap to the flue dimensions. Parts are measured against the actual opening, not ordered by guesswork.
- 3
Test. We verify draft with the cap and damper in place, check the damper operates freely through its full range, and confirm the crown seals and the screen is clear. Smoke should go up and out, not back into the firebox.
- 4
Warranty and documentation. You get the camera inspection photos, a photo report of the finished work, and a written record of what was repaired and what parts were used – which is what you need if a manufacturer’s warranty question ever comes up.
See the difference
Before
After
Before
After
Before
AfterGelco Products We Service & Install in Abilene
We service and install the Gelco product lines most Abilene homes actually have on the roof. Gelco Multi-Flue Caps, in stainless steel and black powder-coated, are the big one – one lid covering several flues on a masonry chimney, which is common on the older brick fireplaces around the historic core. Gelco Custom Chimney Caps are fabricated to the flue dimensions, which is what you need on a non-standard opening. Gelco Single-Flue Caps with mesh spark screens handle the standard single-flue job, and Gelco Top-Sealing Dampers are the energy-saving damper that seals the flue at the top rather than the throat. We service, repair, and install all of these. We don’t claim to stock any of them – we spec and fit to your flue.
We Also Service These Brands
Gelco is one brand in a broader tool kit. We also work with DuraFlex flexible liner systems for flues with offsets or non-standard configurations, and HeatShield ceramic resurfacing for liner restoration when the flue doesn’t need full replacement. One company covers the whole chimney – sweep, inspection, and repair – so you’re not coordinating three contractors when a job turns up more than one problem.
FAQs – Gelco Chimney Cleaning Service in Abilene
No. We’re an independent Gelco service provider, not affiliated with or authorized by the Gelco brand. We work on Gelco caps and dampers because they’re common in Abilene homes, not because of a factory relationship. Call (888) 359-2615 for a free estimate.
Yes. We spec parts that match the mounting pattern, gasket profile, and flue dimensions of your existing Gelco unit. We don’t claim to stock genuine Gelco parts – we measure and match. Where an exact-fit part matters for warranty continuity, that’s what we recommend.
Most Gelco service calls – gasket replacement, cap re-seat, screen cleaning – are done within the same visit as the sweep and inspection, typically a couple of hours on site. A custom cap fabrication takes longer, since the cap has to be made to the flue dimensions. We quote timelines with the written estimate before we start.
We cover Gelco Multi-Flue Caps (stainless and powder-coated), Gelco Custom Chimney Caps, Gelco Single-Flue Caps with mesh spark screens, and the Gelco Top-Sealing Damper. That’s the full range of what Gelco makes for chimneys, and what shows up on Abilene roofs.
Yes, in most cases. The gasket is the wear part, and a hardened or torn gasket can be replaced without touching the damper housing. We inspect the housing and linkage first – if they’re structurally sound, the gasket swap is the repair. Replacement only comes up when the housing or frame has failed. Call (888) 359-2615 for a free estimate.
Usually because the mounting legs have loosened at the bolts or corroded through, so the cap sits unevenly and lifts in the wind. The rattle is the tell; water follows because the loose cap lets rain run down around the crown instead of shedding it. We check torque, bolt condition, and the crown seal on every cap service.
Yes. Direct West Texas sun chalks and peels powder coat over time, and once the bare steel shows, rust sets in at the panel edges and seams. Blowing caliche dust and mesquite pollen also pack the mesh, which chokes draft. A repaint or replacement before the rust pits saves the frame; a screen cleaning each sweep keeps the draft.
The cap has to match the actual flue opening and the number of flues on a masonry chimney. We measure the opening, the crown dimensions, and the flue count, then spec the right size – and yes, a custom Gelco cap can be fabricated to fit a non-standard flue. Call (888) 359-2615 for a free estimate.
It can, because a top-sealing damper shuts the flue at the roof rather than the throat, which stops the draft that pulls heated air up the chimney when the fireplace is idle. In Abilene, where winter northers can swing temperatures 40 degrees in hours, that matters – a sealed flue holds heat in the house during a cold snap instead of bleeding it. The seal depends on the gasket staying intact, which is why we check it every sweep. Call (888) 359-2615 for a free estimate.
A standard sweep with an inspection typically runs a flat price agreed before booking, and Gelco cap or damper repair is quoted separately based on what we find. Nothing is recommended without camera evidence you can see for yourself, and we’ll tell you plainly when work can safely wait. Call (888) 359-2615 for an exact quote – estimates are free.
Book Your Gelco Service in Abilene, TX
If you’ve got a Gelco cap or damper on your chimney in Abilene, book a sweep and inspection and let us check the hardware while we’re there. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Call (888) 359-2615 for a free estimate, and we’ll measure the flue, check the seal, and quote the work in writing before anything starts.
Written by the team at Chimney Sweep Abilene.